PTFE трубка с наилучшей химической стойкостью к коррозии
Базовая информация
Модель: HY-P330H
Описание продукта
Номер модели: HY-P330H Вид: Прочность на сжатие трубки PTFE: <0,4% Кажущаяся плотность: 2,10 ~ 2,30 Относительное удлинение трещины (мин): ≥230% Спецификация: SGS Код HS: 39209910 Материал: PTFE Водопоглощение: 1,5% ~ 3,5% Прочность на растяжение: (81 ~ 130) MPa Прочность на растяжение (мин.): 18 MPa Товарный знак: hysealing Происхождение: Cixi China
Описание:
Трубка PTFE HYP330H формована, прессована или прессована из 100% чистого PTFE. Он обладает лучшей устойчивостью к химической коррозии среди известных пластмасс. Без старения, низкий коэффициент трения, износостойкость. Рабочий диапазон температур без нагрузки составляет -180 ~ + 260 ° C.
Характеристики:
III, Основные свойства:
Описание:
Трубка PTFE HYP330H формована, прессована или прессована из 100% чистого PTFE. Он обладает лучшей устойчивостью к химической коррозии среди известных пластмасс. Без старения, низкий коэффициент трения, износостойкость. Рабочий диапазон температур без нагрузки составляет -180 ~ + 260 ° C.
Характеристики:
Type |
Specifications |
||
OD(mm) |
Wall Thick.(mm) |
Length(mm) |
|
Pressed Pipe |
1~25 |
0.1~2.5 |
Up to your requirement |
Extruded Pipe |
25~200 |
1.5~8 |
Up to your requirement |
Die Pressed Pipe |
25~1800 |
5~500 |
100~1000 |
III, Основные свойства:
Properties |
Unit |
Result |
Apparent Density |
g/cm 3 |
2.10~2.30 |
Tensile Strength(min) |
≥Mpa |
18 |
Crack Elongation(min) |
≥% |
230 |
Item |
Filler | Filler Content by Weight % | Properties | Applications |
1 | Glass filled PTFE | 5 - 40 | High compressive strength | Ball valve component, bridge |
Excellent chemical resistance | bearing pads, ship launching | |||
Improved wear resistance under load & permanent deformation | pads, pipe supporting pads. | |||
2 | Carbon/Coke filled PTFE(soft amorphous/ hard fiber) | 10 - 35 | High compressive strength | Rider and piston rings of air compressor |
Improved wear resistance under load & permanent deformation | ||||
Better thermal / electrical conductivity. | ||||
3 | Graphite filled PTFE(pure crystalline carbon) | 515 | High compressive strength | Used as shaft bearings and in chemical high speed Chemical pumps. |
Improved wear resistance under load & permanent deformation | ||||
Better thermal / electrical conductivity. | ||||
Good chemical resistance | ||||
Improved frictional properties. | ||||
4 | Bronze filled PTFE(oxidising / Non oxidising) | 40 - 60 | High compressive strength | Wear strips Machine tool liners, hydraulic seals. |
Excellent wear resistance improved under load & permanent deformation | ||||
Better thermal / electrical conductivity. | ||||
Good chemical resistance | ||||
Very low cold flow. | ||||
5 | Bronze plus, Molybdenum Disulphide filled PTFE | 55 + 5 | Improved fictional properties | Hydraulic seals. |
High compressive strength | ||||
Excellent wear resistance improved under load & permanent deformation | ||||
Good thermal / electrical conductivity. | ||||
Very low cold flow. | ||||
6 | Aluminium Oxide filled PTFE | 510 | Excellent electrical properties | Electrical insulators in circuit breaker |
Excellent compressive strength | ||||
Excellent wear resistance improved under load & permanent deformation | ||||
7 | Calcium Fluoride filled PTFE | 510 | Excellent chemical resistance | Mechanical seal parts. |
Improved wear resistance under load & permanent deformation | ||||
Excellent compressive strength | ||||
Good with chemicals that attack glass | ||||
8 | Stainless Steel filled PTFE | 510 | Excellent chemical resistance | High Pressure chemical handling equipments. |
Outstanding mechanical properties | ||||
Good wear resistance | ||||
9 | Mica filled PTFE | 510 | Excellent compressive strength | Electrical and thermal insulation pads under compressive loads. |
Very low coefficient of thermal expansion | ||||
Poor tensile properties | ||||
10 | Glass + MoS2 filled PTFE | 15 + 5 | High compressive strength | Low torque valve components |
Excellent chemical resistance | ||||
Improved wear resistance under load & permanent deformation | ||||
Improved frictional properties | ||||
11 | Pigmented PTFE |
|
Improved Visibility | Colour coded electrical cable sheathings |
Группа Продуктов : Изделия из фторопласта
Premium Related Products
Другие продукты
Горячие продукты
Уплотнительная прокладка Hy-T900gcНеасбестовый уплотнительный листГильотинный уплотнитель для упаковки Hy-T900PCМашина для склеивания плит с 8 несущими квадратами с 2 орбитамиМашина для прокладки прокладок малого размера SwgТканевая ткань из стекловолокна для огневой изоляцииТекстильная ткань Волоконная ткань E- GlassКерамическая вставка из квадратного волокна с металлической проволокойЛиния для производства неасбестовой прокладкиУплотнительная прокладка для масляной прокладки без асбестаРезиновое уплотнительное кольцо для уплотнения прокладокPTFE / тефлон с масляной смазанной плетеной упаковкой,Уплотненная графитовая прокладка с автоматической смазкойГибкая прокладка из графита с кольцом уплотнительной манжеты Hy-уплотнение Hy-G410Сальниковое уплотнение с спиральным уплотнением с ASME Swg 316 / Fg / CSСпирально-навитое уплотнение с Asme B16.20 16.47